How to Replace a Bathtub in Your Bathroom
How to Replace a Bathtub in Your Bathroom
Blog Article
We've stumbled upon this post on A Step-by-Step Guide to Installing a Bathtub below on the internet and thought it made good sense to talk about it with you on this page.
Installing a bath tub isn't precisely rocket science, however it does require strong plumbing, carpentry, and also often, tiling abilities. Changing an old bath tub with a new one is additionally a moderately challenging project. If the old tub is conveniently easily accessible, the job can move easily; if you have to open up a wall surface to eliminate the old bathtub as well as place the brand-new bathtub, the task is a lot harder. In either situation, the job is within a house handyman's abilities, although you will need a helper to leave the old bathtub and embeded in the brand-new one. Make sure you have qualified on your own for the work and fit attempting it. Instead of employing a contractor to take over a halfway-completed job, it is far better to take into consideration employing one prior to you begin. Possibilities are you might require an expert plumber to make tube connections.
This write-up will certainly help you mount a new bath tub in your shower room if you have currently purchased a brand-new tub and do not need to alter the arrangement of your previous supply of water pipelines.
Your devices and also product checklist need to comprise the following:
Preparing for the Installment
Firstly, the sustaining frame provided with the bath must be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to make certain that if the tap includes a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets unit to prevent stress on the bath tub.
Fit the flexible tap adapters to the bottom of both faucets using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you make use of every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom must currently prepare to be fitted in its final setting.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you should do is disconnect the water system. After doing so, activate the taps to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be rather troublesome as a result of the limited access that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a towel ready for the staying water that will certainly come from the pipes. When the supply pipelines have been removed, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from transforming throughout this process. When the taps have been removed, the holes in the bath/basin will have to be cleansed of any kind of old securing substance.
Prior to carrying on to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bathtub
Using both wood boards under its feet, put the tub in the required position. The wood boards are handy in equally spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be attained by inspecting the spirit level and changing the feet on the bath tub up until the level checks out degree.
To set up faucets, fit the bottom of the outermost flexible faucet connector to the proper supply pipe by making a compression sign up with; then do the very same for the various other tap.
Activate the supply of water and also inspect all joints and also new pipework for leakages as well as tighten them if necessary. Fill up the bathtub as well as also examine the overflow outlet and also the normal electrical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the maker's instruction manual. Tiling and also sealing around the bath tub ought to wait till the bathtub has actually been used a minimum of when as this will resolve it into its last placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end offers a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the tap in the installing hole in the bath/basin making certain that the washers are in location in between the tap as well as the sink. Safeguard the tap in place with the maker given backnut. Once the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with regular faucet connectors. The former kind needs to be attached to the tap ends initially, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to crack a rigid seal, triggering the water to permeate the wall surface in between the bathroom and also the tiling, leading to complications with dampness as well as possible leakages to the ceiling listed below.
You can select from a selection of coloured sealers to assimilate your components and also installations. They are sold in tubes and cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to constantly load the bath tub with water prior to securing, to enable the motion experienced when the bathtub is in use. The sealant can break fairly early if you do not consider this movement before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily available on the marketplace. It is suggested to fit the floor tiles utilizing water-resistant or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our part about A Step-by-Step Guide to Installing a Bathtub. Thank you for taking the time to read our piece. Loved our article? Please share it. Let someone else check it out. Thanks a lot for your time invested reading it.
Request Free Estimate Report this page